Homeowner FAQs

Many original HVAC systems were not correctly sized. Traditionally the practice of builders using the low bid contractor, to install HVAC systems in new homes, resulted in corners being cut by those contractors. The only way to know if a system is sized correctly is to calculate the existing heating and cooling loads (unless the contractor installed the system and still has the original load calculations). I would avoid using any contractor not willing or capable of doing a Manual J, or an equivalent load calculation, on your home.

To help consumers, ACCA developed a consumer checklist and made it available for free download at our web site — you can download the residential checklist here. I would recommend utilizing the check list to evaluate contractors.

Use ACCA’s online contractor to find contractors at: https://www.acca.org/locator — but remember, even if the contractor is an ACCA member, you still need to do your “due diligence” and ask the important questions, check references, and do research on the company. Use the QI checklists to compare potential providers, so you can see what value you’re really getting for your dollar, and don’t ever hire a contractor who tells you that a Manual J is a “waste of time” when you’re replacing a system. By saying so they have proven that they have very little experience in the field, especially since in many regions it’s required by law — and it’s always the right thing to do.

NJACCA does not have the type of rating information you are requesting. However, on our web site you will find valuable information on how to select a contractor who can install the HVAC equipment following all of the HVAC Quality Installation Design and installation procedures. Any manufacturer’s top of their line HVAC equipment will exceed your expectations for quality and efficiency if it is installed correctly by a professional contractor. For the best results be sure to check out the Quality Installation Checklists.

Just because a filter is available on store shelves and advertised as longer lasting and more efficient doesn’t mean it is appropriate for your furnace. In order to properly select a filter for your home HVAC system, you need more information than most filter manufacturers provide at your local supermarket or hardware store. For example, if the average consumer sees an advertisement that says “increased efficiency” on the filter box, they immediately think the operating cost for using the filter will be reduced. However, in most cases they would be wrong.

If an ad reads “increased filter life due to pleated design,” buyers might also assume that the filter will last longer than the standard one that came with the furnace. Again, that may not be true. The truth in the filters’ advertising is based on the definitions used by filter manufacturers for designing and evaluating filters. The bottom line is buyer beware.

Let’s examine what “more efficient” means in filter design language. It means the filter will remove smaller particles in larger quantities. Since the average one-inch deep throwaway furnace filter is only designed to remove large particles, it is not very efficient in the language of filter design. However, when it comes to the energy required to move air through the HVAC system, those “inefficient filters” work really well. This is because the larger openings in the inefficient filters require less force to pull air through them.

Using an aftermarket “efficient filter” with the same blower operating inside of the HVAC system means you may end up with less total airflow because it requires more force to get the air through it. Therefore, the only way to regain the correct airflow is to increase the blower’s speed. The faster a blower goes, the more power it takes to operate it. To make things worse, the actual power required to operate your HVAC system grows geometrically when motor speed is increased. This means for even a minimal increase in airflow, the power required increases dramatically, along with the related operating expense.

Not always, unfortunately. The total efficiency is dependent on the filter’s holder too. Simply sliding a higher efficiency 1 inch filter into a standard one-inch slot will not stop some of the airflow from bypassing the filter. The higher the efficiency rating of the filter, the more robust the cabinet design and filter rack must be to prevent bypass leakage.

It’s a definite maybe. Let’s take a closer look at the claim of a longer life due to pleated design. First off, it is absolutely true that the pleated design increases the surface area of the filter. Thus, it follows that the filter pleated design with its larger surface area will last longer than the smaller, flat-surfaced filter. Still, this is only true if they are made of identical filtering material. Generally, pleated filters are made of more efficient filtering materials than the standard flat throw-away filters. Since they are more efficient than the flat filters they are replacing, the comparison to the existing filter is like comparing a fish net for catching gold fish to a large shark net. The bottom line is that there is no way to tell if the replacement filter will last longer than the original one other than putting a filter in. It all depends on the type and size of the filter, and amount of dust in your home.

HVAC systems are carefully designed and balanced complex heat-transferring machines. Heat exchangers are used to transfer the heat to the air in an HVAC system. To work properly, these heat exchangers are designed to operate with a minimum and a maximum airflow going through them. In the worst case heating scenarios, low airflow in a furnace can cause short cycling by tripping the high temperature safety switch. Low airflow through the cooling coil could cause it to ice up, resulting in cooling failures or, worse yet, flooding.

Make sure the filter you select is compatible with the design specifications of the HVAC system. Obviously, if you want to increase your filter’s efficiency to have cleaner air there must be a way to do it, and there is. However, it takes someone who can understand your personal filtration requirements and then marry them with your HVAC equipment’s airflow requirements. For your HVAC system to work properly, the person working on it must be able to:

  • Specify filter type based on your requirements
  • Design the installation, including controls and ducting
  • Install the ducting and controls as designed
  • Test the new filtration unit to make sure the HVAC system has the required airflow

As you may have guessed by now, it is not the clerk in the supermarket filter aisle. If you want your home HVAC system to remove household dust, plant spores, pet dander, or more exotic odors, etc., you should consult with an expert. You need to call a professional HVAC contractor so the result is a filtration system that meets your needs and will work properly with your HVAC equipment. HVAC contractors provide filtration systems to satisfy every customer’s needs.